On this page in the next paragraph you can get additional exceptional advice involving How to Install a Bathtub Yourself.
Mounting a bathtub isn't specifically brain surgery, however it does need strong plumbing, carpentry, as well as sometimes, tiling skills. Replacing an old tub with a new one is additionally a reasonably difficult task. If the old tub is readily easily accessible, the project can move rapidly; if you have to open a wall to remove the old tub as well as position the brand-new bath tub, the job is a lot harder. In either instance, the project is within a home handyman's abilities, although you will certainly need a helper to leave the old tub and also embeded in the new one. Make certain you have actually qualified yourself for the work and also are comfortable attempting it. As opposed to working with a contractor to take control of a halfway-completed task, it is much better to consider using one prior to you start. Opportunities are you might require a professional plumber to make tube connections.
This short article will certainly aid you install a new tub in your washroom if you have already gotten a brand-new bathtub and don't require to alter the setup of your previous water pipes.
Your tools and also product list ought to consist of the following:
Preparing for the Setup
To start with, the supporting structure provided with the bath should be fitted (if called for) according to the supplier's instructions. Next, fit the taps or mixer to the bathtub. When fitting the faucet block, it is important to make certain that if the tap comes with a plastic washer, it is fitted in between the bath and also the faucets. On a plastic bathroom, it is additionally sensible to fit a sustaining plate under the taps system to prevent stress on the bath tub.
Fit the adaptable faucet connectors to the bottom of the two taps making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. Make sure you use all of the supplied washers.
Connect the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bath should now be ready to be suited its final setting.
Removing Old Taps
If you need to change old faucets with new ones as a part of your installment, after that the first thing you ought to do is disconnect the water. After doing so, turn on the taps to drain any kind of water continuing to be in the system. The process of removing the existing taps can be quite troublesome because of the limited accessibility that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the faucets. Have a fabric all set for the remaining water that will originate from the pipes. When the supply pipelines have been removed, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will need to stop the solitary taps from transforming during this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleaned up of any old sealing compound.
Before going on to fit the brand-new faucets, contrast the pipe connections on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Mounting the Tub
Utilizing the two wooden boards under its feet, put the bath tub in the called for setting. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards rather than focusing all the weight onto 4 little points.
The following objective is to guarantee that the bath tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub up until the spirit level reviews level.
To mount faucets, fit the bottom of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the exact same for the other faucet.
Turn on the water and also inspect all joints as well as brand-new pipework for leakages as well as tighten them if needed. Load the bath tub and likewise check the overflow outlet and also the normal outlet for leakages.
Ultimately, fix the bathroom paneling as explained in the maker's user's manual. Tiling and securing around the bath tub needs to wait till the tub has actually been utilized at the very least when as this will certainly resolve it right into its last setting.
Suitable New Touches
If the tails of the new taps are plastic, then you will need a plastic connector to stop damages to the string. One end of the port fits on the plastic tail of the tap and also the various other end provides a connection to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin ensuring that the washing machines remain in area between the faucet and also the sink. Safeguard the faucet in position with the supplier supplied backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with regular faucet connectors. The former kind ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the area where the bath fulfills the ceramic tile, it is needed to seal the joins with a silicone rubber caulking. This is very important as the installation can relocate sufficient to break a rigid seal, triggering the water to penetrate the wall in between the bathroom and the tiling, leading to complications with dampness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your components and installations. They are marketed in tubes and also cartridges, and can sealing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to load, you can load it with twists of drenched newspaper or soft rope. Keep in mind to always fill up the bathtub with water prior to securing, to permit the motion experienced when the bathtub is in use. The sealant can split fairly very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily offered on the market. It is suggested to fit the floor tiles making use of waterproof or water-proof sticky as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a keen person who reads on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that portion was worthwhile. Enjoyed reading our blog entry? Please share it. Let others find it. Thank-you for going through it.
High-quality repairs here.